People nowadays are addicted to easy living. They consider it a huge problem when it comes to doing things that include hard work.
So technology came up with ease and introduced electric bikes to your lives, which are a lot more convenient and reliable than a normal bike.
But the electric bikes may result in some inconvenience and could have some issues as well. These issues can make your easy life a hard one. issues like LCD not working are common in Rad Power bike users.
We also encountered a similarly awkward situation and did thorough research to find out the reasons and their possible solutions for the Rad Power Bike LCD Display not working.
In this article, I am going to explain to you all of the possible reasons and their solutions for the Rad Power Bike LCD Display not working.
So, let’s get started.
Reasons and their possible solutions for Rad Power Bike LCD Display not working
Your Rad Power Bike’s LCD may not be working for several reasons. These potential reasons are Wiring Issues, Battery Issues, Controller issues, Blown fuse, Faulty LCD Display unit, Faulty sensors, Faulty switches, and software issues.
1. Wiring Issues
One of the most frequent causes of your Rad Power Bike LCD not working is a loose or disconnected wire connection.
The wires may have fallen loose due to riding-related vibrations or unintentional handling errors, interrupting the electrical connection between your bike’s electronics and the display
Solutions
There are the following solutions if your Rad Power Bike LCD Display not working due to a problem with wire connections:
You should carefully examine all of the LCD’s wire connections. Make sure that they are plugged in tightly and are not loose.
You should push back any connections that are loose into place gently. To create a strong connection, make sure they are seated correctly for a stable connection.
You have to deeply look for any obvious evidence of damage, such as cuts, fraying, or wear, on the wires. It could be necessary to replace the wire if you find any damage.
2. Battery issues
The LCD won’t turn on if its power source runs out of fuel or has a low charge.
Solutions
If your Rad Power Bike is not working due to battery issues, here are some steps you can take to troubleshoot and potentially resolve the problem.
You should observe that the electrical system of your bike is properly and securely connected to the battery. While riding, the battery of your Rad Power Bike may occasionally get somewhat loose and cause connectivity problems.
The battery should be connected to the charger, and the suggested charging time should be followed if it is low at a charge. Verify whether the charger’s LED shows that it is charging.
You should clean the battery terminals and the matching connectors on the bike for corrosion, debris, or anything else that can obstruct the electrical connection.
You should try a different battery to power your bike. It will help to determine whether the problem is with the original battery or other parts.
Check your Rad Power Bike battery health status, which may be either on the battery or on the LCD display. The battery might need to be replaced if it has considerably deteriorated.
A diagnostic feature on your Rad Power Bikes shows problem codes relating to the battery. To detect and resolve any error codes, consult the bike’s user manual.
3. Controller Issues
There may be issues with the electronic controller for the bike, which controls several features, including the LCD.
Solutions
A controller issue may be the cause of your Rad Power Bike LCD not working. Here are some ways to aid in problem diagnosis and potential resolution:
You have to examine the connections between the controller and the LCD. Ensure that all cables are plugged in firmly. The display may not function properly due to loose or damaged connections.
You should look carefully for any apparent signs of damage or moisture infiltration on the controller unit of your Rad Power Bike. The controller functions may be hampered by physical damage.
Your Rad Power bike has the feature to reset the controller, which may resolve temporary issues.
A reset can be done by following these steps
- You should turn off your bike completely.
- Find the primary power wire that links the battery to the controller if your bike has an integrated battery. To turn off the controller’s power, gently unplug this primary wire.
- Wait for a few minutes, this waiting period will fully discharge the controller capacitor.
- Re-insert the main power connector into its socket, to give the controller power again
- Restart the bicycle to check whether the controller has been reset and is working properly.
4. Blown Fuse
Due to overload, electrical components overheat or certain wires become shorted, which results in a blown fuse. A blown fuse could be a reason for the Rad Power Bike LCD Display not working.
Solutions
- Turn off the bike to ensure that your bike has no power flowing through the electrical system.
- Open the fuse box which is located near the battery compartment or controller unit.
- You should carefully check the fuses by opening the fuse box. Be on alert for any fuses that seem to be burned out, fractured, or that have a clear gap in the metal strip inside the fuse. These symptoms indicate a blown fuse.
- If you find a blown fuse, take it out of the fuse holder and replace it with a fresh fuse with the same rating. The proper fuse is present either on the fuse itself or in the bike’s user manual.
- Reconnect the battery to the bike after replacing the blown fuse
- Start the bike and check that LCDs operating properly.
5. Faulty LCD Display Unit
The LCD unit itself may have developed a problem or damage owing to a variety of reasons, such as moisture exposure, impacts, or manufacturing flaws, just like any other electronic component.
Solutions
Here are the actions you can take to solve the problem if the LCD display unit on your Rad Power Bike is malfunctioning.
Look for any obvious physical damage to the LCD unit, such as fractures, water damage, or broken parts.
Physical damage is frequently an apparent indication of a malfunctioning display.
To see if the issue is with the original LCD Display unit, you should try a compatible LCD unit from another bike.
Rad Power Bikes require careful handling and close attention while replacing a defective LCD unit.
Make sure you have the required tools and technical knowledge before attempting the replacement, or if you’re not confident you can handle it, think about getting professional help.
6. Faulty Sensors
Data like the speed and pedal cadence of your Rad Bike are collected by sensors and displayed on the LCD screen.
The problem of the Rad Power Bike LCD Display not working may arise from one or more of these sensors not working properly.
Solutions
Here are some measures you can take to solve the problem if your Rad Power Bike’s sensors are malfunctioning:
Identify sensors that are the source of the issue for your bike LCD. Rad Power Bikes frequently make use of a variety of sensors, including torque, pedal cadence, and speed sensors.
The particular sensors may have to change if it’s affecting LCD Display.
You should examine the wiring of the problematic sensors. Make sure the connectors of sensors and LCD Display are plugged in firmly and are not loose.
The connectors can occasionally fall loose due to vibrations during riding.
Clean the sensors if they have magnetic contacts, and check that they are clear of any dirt or anything that can obstruct their proper operation.
You might need to replace a faulty sensor. To get the appropriate replacement sensor for your bike model, get in touch with Rad Power Bikes’ customer care or an authorized dealer.
7. Faulty switches
The throttle has a power button that can be used to start the motorcycle. Function keys are also used to set or reset the display.
It won’t be possible to switch on the display if one of these buttons is broken.
Solutions
You should look for any physical damage, such as cracks, broken buttons, or water damage, on the throttle switches.
You should clean the area close to the switches using a soft brush or compressed air to make it free from dust and debris.
To test whether each button is smoothly engaging and registering, press it or turn the throttle to check its functionality.
You might need to replace the throttle switch if you’ve found one that’s broken. To get the proper replacement throttle for your bike model, get in touch with Rad Power Bikes’ customer care or an authorized dealer.
8. Software issues
Verify if the LCD has any available software upgrades. A firmware upgrade may fix the issue if it is brought on by a software bug.
Solutions
There are the following solutions if your Rad Power Bike LCD Display not working due to software issues.
You should check out if your bike model has any available software upgrades, you should visit the Rad Power Bikes website or get in touch with customer service. Updates from companies are frequently released to address issues and enhance system stability.
- The Rad Power Bikes update files should be saved to your computer if a software upgrade is available.
- Put the updated files you downloaded to your computer in the root directory of the USB device. Instead of putting the data in a folder, it should be put directly on the USB drive. Make sure the USB drive’s file system, which is frequently compatible is FAT32.
- Put the USB drive into the correct port on your bike’s display or controller.
- Be sure to follow any instructions that may show on the screen while the bike’s display is being updated. Refrain from turning off the bike or removing the USB drive until the update is complete.
Final Thoughts
In this article, I have discussed with you all the possible reasons and their solutions for the Rad Power LCD Display not working. I have explained these causes and solutions in depth.
Hopefully, this article will cover all the things you need to know about Rad Power Bike LCD Display not working. You can get in touch with us through our contact page if you want to share something about the Rad Power Bike LCD Display not working.
Do I need to hire a professional to replace the LCD on my Rad Power Bike if it is not working?
If you have the technical know-how and decide to replace the LCD, it’s important to move carefully to prevent further damage. The best course of action is to get expert assistance from a licensed service facility or the support staff at Rad Power Bikes if you lack the confidence to complete the task yourself.